|
|
Post by stormoffires on Mar 15, 2014 7:06:45 GMT -6
drive.google.com/file/d/0B7I4FfX-IJY9WWZyYkx0TFR4RVE/edit?usp=sharingi have installed pods on my bike, it runs with the standard #125 jets however if i go full throttle to quickly it will bog the engine down (obviously to much air to fuel so jets will be changed) but my question, i am probably gonna order the PAIR removal kit, get those hoses out of their, but my question is i read people talk about routing another hose into their pods for another breather but i dont know what you guys are talking about, is it that hole below the carbs? *side note* bike seems to have fuel leak from the "off/res/pri" valve, i think its a vacuum valve but i don't know what i can do about replacing it/fixing it any ideas?
|
|
|
|
Post by Blaine on Mar 15, 2014 13:52:07 GMT -6
drive.google.com/file/d/0B7I4FfX-IJY9WWZyYkx0TFR4RVE/edit?usp=sharingi have installed pods on my bike, it runs with the standard #125 jets however if i go full throttle to quickly it will bog the engine down (obviously to much air to fuel so jets will be changed) but my question, i am probably gonna order the PAIR removal kit, get those hoses out of their, but my question is i read people talk about routing another hose into their pods for another breather but i dont know what you guys are talking about, is it that hole below the carbs? *side note* bike seems to have fuel leak from the "off/res/pri" valve, i think its a vacuum valve but i don't know what i can do about replacing it/fixing it any ideas? They are talking about the engine breather hose ( one behind the starter).It should have a filter of it's own when you shift to pods.Your on the right track changing the jets to bigger ones.If that don't cure your bogging you can cut a couple of coils off the top of the slide springs.The valve that is leaking is your petcock.You can get a rebuild kit for it or replace it.   |
|
|
|
Post by stormoffires on Mar 15, 2014 17:53:39 GMT -6
ok well im unsure of what the engine breather hose is for the engine then, can ya provide any pictures by chance?
|
|
|
|
Post by Blaine on Mar 15, 2014 21:08:01 GMT -6
ok well im unsure of what the engine breather hose is for the engine then, can ya provide any pictures by chance? It the odd shaped one that ran from the bottom of the air box to the engine.Now that it's disconnected from the airbox it needs it's own filter. |
|
lamestlame
Junior Member
So I am recovering from an accident I had on my ninja. More bonding time with my trusty ol 454 ;)
Posts: 220
|
Post by lamestlame on Mar 16, 2014 22:30:28 GMT -6
If you don't have a filter on it you can feel the air coming from it while the bike is running.
|
|
|
|
Post by eaglerider on Mar 17, 2014 13:43:05 GMT -6
It connects to the round cover, likely silver in color, (about 2 or 3 inch diameter) near the starter. It has a little pipe for a hose connection sticking out of it.
|
|
|
|
Post by stormoffires on Mar 17, 2014 16:28:02 GMT -6
oh so the hole in the picture i provided? what did yyou guys use to filter it.
|
|
|
|
Post by Blaine on Mar 17, 2014 17:19:27 GMT -6
oh so the hole in the picture i provided? what did yyou guys use to filter it. Yep that's it.Sorry I hadn't seen the pic till now.It's easier to use the bottom half of the original hose & add a small filter to it.  |
|
|
|
Post by stormoffires on Mar 18, 2014 6:14:06 GMT -6
yikes, so no extra hoses came off my airbox.. im starting to think i never had a hose around the breather >_< only 1 hose came off and that ran to the PAIR system up top.
|
|
|
|
Post by Blaine on Mar 18, 2014 15:16:24 GMT -6
yikes, so no extra hoses came off my airbox.. im starting to think i never had a hose around the breather >_< only 1 hose came off and that ran to the PAIR system up top. There is a hole about 3/4" near the bottom on the front of the airbox.The hose runs from there to the engine. |
|
lamestlame
Junior Member
So I am recovering from an accident I had on my ninja. More bonding time with my trusty ol 454 ;)
Posts: 220
|
Post by lamestlame on Mar 24, 2014 22:34:44 GMT -6
How did you guy's block off the top to holes? I want it to look cleaner. Thanks for any response (:.
|
|
|
|
Post by Blaine on Mar 25, 2014 5:04:18 GMT -6
|
|
|
|
Post by stormoffires on Mar 26, 2014 16:52:01 GMT -6
just got that PAIR removal kit, gonna put it on when i go to do a valve adjustment.
|
|
|
|
Post by BenInPA on Mar 27, 2014 18:48:05 GMT -6
Hey storm, did you get the gaskets with it? If you did use them. But I would use a little rtv to make a good seal. Don't forget to read the directions for it. I have removed the pair on mine as well with the kit. You will have to pull the thing right under the cover out and remove part of it. That's why I said read the instructions. It tells you how to remove and what to remove. You will be putting the thing back in. Good luck man.
Sent from my DROID RAZR using proboards
|
|
|
|
Post by stormoffires on Mar 30, 2014 6:51:58 GMT -6
Hey storm, did you get the gaskets with it? If you did use them. But I would use a little rtv to make a good seal. Don't forget to read the directions for it. I have removed the pair on mine as well with the kit. You will have to pull the thing right under the cover out and remove part of it. That's why I said read the instructions. It tells you how to remove and what to remove. You will be putting the thing back in. Good luck man. Sent from my DROID RAZR using proboards ya i got the gaskets, and it has a good seal, did a test ride without RTV and it has no issues, the gaskets give it a good seal. I removed everything but i dont know why I would be putting the "thing" (PAIR?) back in? |
|
|
|
Post by BenInPA on Mar 30, 2014 13:14:12 GMT -6
I'm not sure it is necessary. The directions with that kit use it. You take the piece out, remove the 2 screws, take the metal piece off and put that back in under the casket. Not sure what the idea of it is, just followed the directions. Have fun man!
Sent from my DROID RAZR using proboards
|
|
|
|
Post by stormoffires on Mar 30, 2014 15:13:50 GMT -6
I'm not sure it is necessary. The directions with that kit use it. You take the piece out, remove the 2 screws, take the metal piece off and put that back in under the casket. Not sure what the idea of it is, just followed the directions. Have fun man! Sent from my DROID RAZR using proboards oooh i know what your talking about, your suppose to skip that part if you use the gaskets it says skip to #14. |
|
